M 2 6 1 4 E S FUJITSU NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders 1334| | | Capacity form/unform 182/ MB Heads 8| | | Seek time / track 20.0/ 5.0 ms Sector/track 68| | | Controller SCSI1 SINGLE-ENDED Precompensation Cache/Buffer 24 KB RING BUFFER Landing Zone Data transfer rate MB/S int Bytes/Sector 256 2.500 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 45 | -40 60 Power: sleep W Humidity % 20 80 | 5 95 standby W Altitude km -0.060 3.000| 12.000 idle W Shock g 5 | 50 seek 10.4 W Rotation RPM 3490 read/write W Acoustic dBA 43 spin-up W ECC Bit - MTBF h 50000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** FUJITSU M2612/M2613/M2614-ES/ESA/ESB OEM MANUAL 41FH5058E-03 +---------------------------------------------------------+ | +---+ |XX | +------+ +--------+ | | |XX | | | +----------+ | | Terminator| |XX | | | | | | | | | |XX | +------+ | | | | +-x-+ |XX | +----------+ +--------+ +--+11 |XX | | | |XX | +--+ +--+ CNH-1 | | |XX | +--+ |x |1 | | |XX | CN6/LED OFF | x| ON | | |XX | |x | +--+ 1 |XX | |x |4 +--+ 9 |XX | +--+ | | |XX | DIP switch CNH-2 | | | | | | | | | | |XX Power | +--+ 1 |XX +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** FUJITSU M2612/M2613/M2614-ES/ESA/ESB OEM MANUAL 41FH5058E-03 Jumper Settings =============== x = Jumpers are set from factory CNH1 SCSI bus parity option ---------------------------- x 1- 2 CLOSE SCSI bus parity is enabled 2- 3 CLOSE SCSI bus parity is disabled CNH1 Synchronous transfer mode ------------------------------- x 4- 5 CLOSE Synchronous 5- 6 CLOSE Asynchronous CNH1 SCSI terminator power --------------------------- x 7- 8 CLOSE Power source for IDD terminator x 10-11 CLOSE ------------------------------- o SCSI bus terminator power source is used # IDD terminator power source is used Others ------ # IDD supplies bus terminator power source 8- 9 CLOSE Power source for IDD terminator 10-11 CLOSE ------------------------------- x SCSI bus terminator power source is used * IDD terminator power source is used Others ------ x IDD supplies bus terminator power source 7- 8 CLOSE Power source for IDD terminator 9-10 CLOSE ------------------------------- * SCSI bus terminator power source is used x IDD terminator power source is used Others ------ x IDD supplies bus terminator power source o = Bus terminator power voltage > IDD terminator power volt. # = Bus terminator power voltage < IDD terminator power volt. * = any condition Power sypply for terminator (+5VDC) +-----------------------------------------------------+ | +----- CNH-1 -----+ -+- +5V DC| +++ | 7 8 9 10 11 | | | | TERMPER +------+ +-+--+--+--+----+-+ + Diode | S *---------+ FUSE +-----+ | | | +------+ | C | +------+ +--+--+----+ | S | +------+-----+ | I *-----------------------------+ Terminator | | | SIGNAL | Circuit | | +++ +------+-----+ | | + GND | +-----------------------------------------------------+ CNH2 SCSI ID / Drive select ---------------------------- 1- 2 CLOSE Bit 0 ON x 2- 3 CLOSE OFF 4- 5 CLOSE Bit 1 ON x 5- 6 CLOSE OFF 7- 8 CLOSE Bit 2 ON x 8- 9 CLOSE OFF DIP Write protect ------------------- 1 ON Write Protect x 1 OFF No Write Protect DIP Motor control ------------------- x 2 ON Self starting mode 2 OFF Wait for Motor Start/Stop Command The starting method of the disk drive spindle motor may be adjusted by by the setting switch on the IDD. If this switch is set to inhibit motor start control, the spindle motor starts immediately after the IDD is turned on. If the setting switch is set to enable motor start control, the motor does not start if the IDD is turned on. In this case, a command is used to start the spindle motor. DIP Self Diagnostic Switch ---------------------------- 3 ON Normal mode x 3 OFF Self-diagnostic mode DIP Not used -------------- 4 ON x 4 OFF MUST BE OFF! ********************************************************************** I N S T A L L ********************************************************************** FUJITSU M2612/M2613/M2614-ES/ESA/ESB OEM MANUAL 41FH5058E-03 Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | x x | | | | | | +------x------x-------+ | +-----+ +-----+ | +-+------x--x-------+-+ +--+ +--+ | xx | | x x | +---x--------x----+ x x There are three possible installation directions, and the mounting angle must be 5* from the horizontal. Dont install the PCA on the top! Ambient temperature ------------------- The operating temperature range of the drive is specified at a dis- tance of 3 cm from the drive. Note, temperature specifications are for the outside air surrounding the drive. Make shure to maintain the base temperature range of DE from 5*C to 58*C. Multi-drive connection ---------------------- Host systems, IDDs, and other SCSI controllers can be connected (daisy-chained) to SCSI provided that the total number of SCSI de- vices connected does not exceed eight. Cable requirements ------------------ A characteristic impedance of 100 10% is recommended for the un- shielded twisted-pair ribbon cable. Characteristic impedance greater than 90 is preferred for the shielded cable. A minimum conductor size of 28 AWG shall be employed. It is recommended that the shielded cable be uses for connection outside the system cabinet. To minimize discontinuities and signal refelections, cables of dif- ferent impedance should not be used on the same bus. The maximum cable length is 7m. A cable length of 1m or more is recommended be- tween SCSI devices. Terminator ---------- Terminator is already installed in IDD at shipment. Remove the ter- minator if the IDD is not installed at beginning or ending position of SCSI cable. The terminator is only installed on the controller PCA when the IDD is connected to the beginning or ending position of SCSI cable. External LED Connection ----------------------- The user can connect the external LED to the drive if necessary. The external LED is connected to CN6 on the PCA. ********************************************************************** G E N E R A L ********************************************************************** FUJITSU => GDT Tips & Hints about ICP controllers and other peripherals ======================================================== Tagged queues and Fujitsu M 26xx harddisks ------------------------------------------ Fujitsu Harddisks of the M26XX series do not support the SCSI-II feature tagged queues. You should disable this feature in the initialize disks menue of the GDTSetup program. An inquiry command shows, that the harddisk supports tagged queues (this is why you can enable it in the GDTSetup) but this is not true as stated by Fujitsu Germany.