M 1 6 0 3 T A U P I C O B I R D 7 FUJITSU NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 3456| 1055| | Capacity form/unform 544/ MB Heads 3| 16| | Seek time / track 10.0/ 3.0 ms Sector/track | 63| | Controller IDE / ATA2 FAST/ENHA Precompensation Cache/Buffer 256 KB Landing Zone Data transfer rate 5.500 MB/S int Bytes/Sector 512 16.700 MB/S ext PIO4 Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep W Humidity % 8 80 | 5 95 standby W Altitude km -0.300 3.000| -0.300 12.000 idle W Shock g 5 | 50 seek W Rotation RPM 5400 read/write W Acoustic dBA 38 spin-up W ECC Bit MTBF h 300000 Warranty Month 24 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** FUJITSU M1603TA/1606TA JUMPER SETTING A1CA 01310-0012 +---------------------------------------------------------+ | | | |XX | |XX | |XX | CNH1 |XX | 9++++++ |XX | ++++++2 |XX | |XX | |XX | |XX | |XX | |XX | |XX | |XX | |XX +5V | |XX RETURN | |XX +12V +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** FUJITSU M1603TA/M1606TA JUMPER SETTING A1CA 01310-0011 Jumper Setting ============== CNH1 Jumper Setting ------------------- +------+--------------------+-------+--------+-------------------+ | Pin | Function | OPEN | CLOSED | Remarks | +------+--------------------+-------+--------+-------------------+ | 1-2 | Drive type select | Slave | Master*| - | +------+--------------------+-------+--------+-------------------+ | 3-4 | RESERVED | | | NOT USED | +------+--------------------+-------+--------+-------------------+ | 5-6 | Auto Idle control | Enable|Disable*| - | +------+--------------------+-------+--------+-------------------+ | 7-8 | CSEL connected to | No* | Yes | Supported needed | | | interface | | | from host (NOTE1)| +------+--------------------+-------+--------+-------------------+ | 9-10 | RESERVED | | | NOT USED | +------+--------------------+-------+--------+-------------------+ NOTE1 CSEL: Cable select mode gives an alternative method by which the drive may be set to MASTER or SLAVE. A special cable is needed to implement this feature and should only be used if supported by BOTH drives. CSEL mode should be used in conjunction with SLAVE and without ACMODE. * = DEFAULT ********************************************************************** I N S T A L L ********************************************************************** FUJITSU M1603TA/M1606TA JUMPER SETTING A1CA 01310-0011 Notes on installation ===================== Drive mounting -------------- horizontally vertically +-----------------+ +--+ +--+ +------------------+ | | | +-----+ +-----+ | | | x | | | | | | | | x+----------------+x +-+-----------------+-+ | | | | | | ||x x|| +---------------------+ | | | | | | || x x || | | | | | | || x x || x x | | | | | | || x x || +------x------x-------+ | +-----+ +-----+ | || xx || +-+------x--x-------+-+ +--+ +--+ || x x || | xx | || x x || | x x | || x x || +---x--------x----+ |x x| x x x++----------------++x UNACCEPTABLE! UNACCEPTABLE! Orientation ----------- The drive may be installed in one of three orientations; PCA down or on either edge. Inclination from vertical or horizontal should not exceed 5*. Mounting screw fixing --------------------- When the mounting screw holes on the side of the drive are used, then use only the two pairs of outer holes. Do not use the centre hole in conjunction with only one of the outer holes. The screw must not penetrate the drive by more than 4.5 millimetres. Grounding --------- Sufficient grounding will be provided for correct operation when the drive is screwed into an electrically grounded frame. Cooling ------- Allow space above and below the drive to provide for adequate air flow. Fan cooling is recommended. The disk enclosure temperature, measured at top centre, should never exceed 60*C.