S T 2 3 8 3 E W R E N SEAGATE NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 5.25"/HH Cylinders 1747| | | Capacity form/unform 338/ 383 MB Heads 7| | | Seek time / track 16.0/ 3.0 ms Sector/track 54| | | Controller ESDI Precompensation 65535 Cache/Buffer KB Landing Zone Data transfer rate 1.875 MB/S int Bytes/Sector 512 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 10 50 | -40 70 Power: sleep W Humidity % 8 80 | 5 95 standby W Altitude km -0.305 3.048| -0.305 12.210 idle W Shock g 10 | 40 seek 19.0 W Rotation RPM 3592 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 40000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** SEAGATE ST2182E/ST2383E PRODUCT MANUAL 77765369-C +--------------------------------------------------------+ | |XX J4 | |XX Data | +-+ |XX Cable | Terminator | | |XX | Resistor | | |X1 | Pack | | | | +-+ |XX | +-+ |XX J3 | | |J2 |XX Control | | | |XX Cable | +-1 |XX | +-+ |XX | | |J8 |XX | +-1 |X1 | | | |XX Power | |XX J1 +--------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** SEAGATE ST2182E/ST2383E PRODUCT MANUAL 77765369-C Jumper setting ============== x = Jumpers are set at factory J1 Power Connector ------------------- +---+---+---+---+ | 1 | 2 | 3 | 4 | +--++--++--++--++ | | | +---------- + 5V | | +-------------- + 5V Return | +------------------ +12V Return +---------------------- +12V J2 Reserved ------------- 1 OPEN RESERVED for factory test J2 Sector Configuration ------------------------ To implement the hard sectored format operation configure the jumpers on the option select header to one of the configurations flagged by the note (4) in the table. The number of sectors chosen should correspond to the same number of sectors per track that the host controller is set up to send when it formats the drive or tries to write or read data to/from the drive. Bytes/Sect| Sectors | 4 | 3 | 2 ----------+---------+-------+-------+--------- 256 | 96 | OPEN | OPEN | OPEN ---+ 512 | 54 | CLOSED| OPEN | OPEN ---+ | 15 | OPEN | CLOSED| OPEN ---+-- 4 ***Custom | N/A | CLOSED| CLOSED| OPEN ---+ x 512 | 53 | OPEN | OPEN | CLOSED ---+ 512 | 51 | CLOSED| OPEN | CLOSED ---+ * | Special | OPEN | CLOSED| CLOSED ** | Address | CLOSED| CLOSED| CLOSED | mark | | | * Special sector switch setting that can be factory configured to customer requirements. Default is 1024 B/Sect. and 38 Sectors ** Soft Sector operation selection. The WREN 6 HH supports the use of the soft sector format. To implement the optional soft sectored format operation select "Address Mark" mode in the WREN 6 HH by installing option jumper plugs 2, 3, and 4. *** Custom setting is reserved for factory configuration to customer requirements. J2 Motor Start on command -------------------------- 5 OPEN Spindle motor starts on power-up CLOSED Spindle motor start command required to start motor J8 Drive select ----------------- Drive 1 2 3 ------+-----+-----+-----+ 0 |OPEN |OPEN |OPEN | Not Valid 1 |CLOSE|OPEN |OPEN | 2 |OPEN |CLOSE|OPEN | 3 |CLOSE|CLOSE|OPEN | 4 |OPEN |OPEN |CLOSE| 5 |CLOSE|OPEN |CLOSE| 6 |OPEN |CLOSE|CLOSE| 7 |CLOSE|CLOSE|CLOSE| Pins on the drive ID select and configuration select header are provided to facilitate manual drive configuration. No devices other than jumpers should be connected to these pins. Connection made to external devices (Switches, Connectors, etc.) could result in adverse affect drive performance. Exact location of these pins and header may be changed without notice. Drive Select ------------ The following characteristics apply to the Drive Select lines: 1. Logical unit designation for up to 7 drives is performed during installation by installing jumpers on pins on a connector header on the main PWA. The jumpers are installed in a 1 through 7 position configuration to select device addresses 1 through 7. Zero is not a valid address. 2. The controller shall not attempt to select the drive until 1 second after DC power is applied. The Ready output will be valid (whether asserted or negated) within 1 us after the drive is selected. 3. The drive will be selected (and the Drive Selected Signal asserted) within 1 us after the Drive Select lines contain that unit's select address. The drive will be deselected (and the Drive Selected signal negated) within 1 us after the Drive Select lines contain another unit's select address. 4. The Drive Select lines must remain asserted for 1 us after a write operation. 5. When the Drive Select lines are asserted, a head change will occur, requiring a delay before a read or write operation can be initiated. ********************************************************************** I N S T A L L ********************************************************************** SEAGATE ST2182E/ST2383E PRODUCT MANUAL 77765369-C Notes on installation ===================== Drive Orientation ----------------- The balanced rotary arm actuator design of the Wren 6 HH allows it to be mounted in any orientation. All drive performance characterization however, has been done with the drive in horizontal (disc level) and vertical (drive on its side) orientations, and these are the two preferred mounting orientations. WREN 6 HH is designed, manufactured, and tested with a "Plug-in and Play" installation philosophy. This minimizes the requirements for highly trained personnel to integrate the WREN 6 HH into an OEM's system, wether in a factory or field environment. Mounting Holes -------------- Mounting Holes (6-32 UNC-2B). Four on bottom, four on each side. Max. screw length into chassis 0.125 in. Front Panel ----------- The WREN 6 HH is available with a black front panel. The panel has a window through which a single red* LED shows from its mounting on the Main PWA. The LED, when glowing, indicates the drive is selected. A flashing LED indicates the presence of a nonrecoverable fault. A fault indication is displayed irrespective of Drive Select status. *Green or Amber LED indicator will be available, but must be specified when ordering units. Cooling ------- Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the WREN 6 HH will not exceed temperature conditions. Specific consideration should be given to make sure adequate air circulation around the components on the PWAs. Interface Cabling Options ------------------------- View A +---------------------Host-Controller---------------------+ | | |Data Control Data Control Data Control Data Control | +--+-----+--------+-----+--------+-----+--------+-----+---+ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | +-++-+--++-+-+ +-++-+--++-+-+ +-++-+--++-+-+ +-++-+--++-+-+ | |T | |*T| | | |T | |*T| | | |T | |*T| | | |T | |*T| | | +--+ +--+ | | +--+ +--+ | | +--+ +--+ | | +--+ +--+ | |WREN OR ESDI| |WREN OR ESDI| |WREN OR ESDI| |WREN OR ESDI| +------------+ +------------+ +------------+ +------------+ Each control cable length must not exceed 10 feet (3.00m). Each data cable length must not exceed 10 feet (3.00m). *T indicates removable terminator resistor pack. WREN data cables are permanently terminated. Radial Configuration -------------------- View A shows each drive interfaced to its own control cable, which allows interfacing an arbitrary number of drives and a variety of system operational techniques. Each drive has its data cable and control cable radially connected to the host controller. The length of each individual cable must not exceed 10 feet (3.00 meters). Terminator resistors must be installed in the host controller for each data cable and for each control cable. For this configuration, a terminator resistor pack must be installed in each WREN 6 HH Disc Drive. View B +--------------Host Controller-------------+ | | |Data Control Data Data | +-+------+-------+--------------+----------+ | | | | | | | | | | | | | +-**----+-------+------+-------+ +++-+----+---+ +++-+-----+--+ +++-+----++-++ ||T | | ||T | | ||T | |*T|| |+--+ | |+--+ | |+--+ +--+| |WREN OR ESDI| |WREN OR ESDI| |WREN OR ESDI| +------------+ +------------+ +------------+ Total control cable length must not exceed 10 feet (3.00m). Each data cable length must not exceed 10 feet (3.00m). *T indicates removable terminator resistor pack. WREN data ports are permanently terminated. ** A maximum of 7 devices may be interconnected Daisychain Configuration ------------------------ A diasychain configuration incorporates a maximum of seven drives in parallel on a common control cable. Only the drive selected by the host system has its control and data signals enabled through this common interface. View B illustrates a daisy-chain of WREN 6 HH Disc Drives or other ESDI devices. A terminator resistor pack is required in the host controller for each data cable. Only the last ESDI device in the daisychain requires a terminator resistor pack for the control cable. Terminator resistor packs for the control cable or other drives must be removed. The total combined control cable length (from the controller to the first drive, to the second and subsequent drives) must not be more than 10 feet (3.00 meters). DC Cable and Connector ---------------------- The WREN 6 HH receives DC power through a 4 pin right angle connector mounted on the main circuit board. Recommended part number for the mating connector are provided, but equivalent parts may be used. Type of cable: 18 AWG Connector: AMP 1-480424-0 Contacts: AMP 60619-4 (Loose Piece); AMP 61117-4 (Strip) Data Cable and Connector ------------------------- The I/O connector for the data interface is a 20 pin board edge connector. The odd pins are located on the back side of the printed circuit board. The even pins are on the front side (down) side of the printed circuit board. A key slot is provided between pins 3 and 5. Seagate recommends keying this connector to prevent installing it upside down. However, the WREN will not be damaged if the connector is installed upside down. Recommended part numbers for the mating connector are included below, but equivalent parts may be used. Connector: 20 pin, 3M-3461-0001, AMP 88373-6 Cable: Flat Cable (Stranded AWG 28) 3M-3365-20 Flat Cable (Stranded AWG 28) 3M-3517-20 (Shielded Cable) Key: AMP 583274-1, 3M-3439-0000 Control Cable and Connector --------------------------- The I/O connector for the control interface is a 34 pin board edge connector. The odd pins are located on the back (up) side of the printed circuit board and are connected to the ground plane. The even pins are on the front (down) side of the printed circuit board. A key slot is provided between pin 3 and 5. Seagate recommends keying this connector to prevent installing it upside down. However, the WREN will not be damaged if the connector is installed upside down. Recommended part numbers for the mating connector are included below, but equivalent parts may be used. Connector: 34 pin, 3M-3463-0001, AMP 88373-3 Key: AMP 583274-1, 3M-3439-0000 Cable: Flat cable (Stranded AWG 28) 3M-3365-34 Flat cable (Stranded AWG 28) 3M-3517-34 (Shielded Cable) Spectra Strip Twist'n Flat 455-248-34 (Stranded AWG 28 Twisted Pair) Interface Drivers/Receivers --------------------------- The WREN 6 HH uses two types of signals; single ended and balanced differential. The data and clock signals use balanced differential drivers and receivers. All other signals use single ended drivers and receivers. Single Ended Drivers/Receivers ------------------------------- Transmitter Characteristics The WREN 6 HH uses the 74F38 open collector buffer/driver to transmit status to the host. This driver is capable of sinking a current of 48 mA with a low-level output voltage of 0.7V. Receiver Characteristics The WREN 6 HH uses the 74LS14 Hex Inverter with hysteresis gate as a line receiver. The input of each receiver is terminated in a 150 ohm pullup resistor. Terminator Characteristics The terminator is a resistor module that plugs into a socket in the last drive in a daisychain. Each drive is furnished with a terminator. Terminators must be removed from all except the last drive on the cable prior to daisychain operation. An equivalent terminator must be provided in the controller on each input signal line from the drive to the controller. Only the control cable resistor module is removable. Balanced Differential Drivers/Receivers --------------------------------------- Transmitter Characteristics The WREN 6 HH uses 8923 balanced differential driver. An assertion on the interface is defined when "+" output is more positive than the "-" output. Receiver Characteristics ------------------------ The WREN 6 HH uses 8923 type balanced differential receivers. An assertion one on the interface is defined when the "+" input is more positive than the "-" input. Terminator Requirements ----------------------- Each differential receiver in the drive is terminated with a 100 ohm resistor. An equivalent terminator must be provided in the controller on each input signal line from the drive to the controller. ********************************************************************** F E A T U R E S ********************************************************************** SEAGATE ST2182E/ST2383E PRODUCT MANUAL 77765369-C General Description ------------------- The WREN 6 HH is a member of a family of low cost, high performance, highly reliable, random access storage devices designed to meet the needs of the OEM marketplace. The Model 94246 WREN 6 HH supports the Enhanced Small Device Specification (77738076). This product specification was created to be used in conjunction with this industry standard interface specification. Standards --------- The WREN 6 HH has been developed as a system peripherals to the highest standards of design and construction. The WREN 6 HH depends upon its equipment to provide adequate power and environment in order to achieve optimum performance and compliance with applicable industry and governmental regualations. Special attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temperature regulation. The WREN 6 HH complies with Seagate standards. The WREN 6 HH, as delivered, is designed for system integration before use. The Head/Disc/Actuator Assembly (HDA) is environmentally sealed at the factory. Air is recirculated within the HDA through a nonreplace- able filter to maintain a contamination free HDA environment. The WREN 6 HH uses a dedicated landing zone at the innermost radius of the media thus eliminating the possibility of destroying or degrading data by landing in the data zone. The WREN 6 HH incorporates an automatic shipping look which prevents potential damage to the heads and discs caused by movements during shipping and handling. The shipping lock is automatically disengaged when power is applied to the drive. The WREN 6 HH decodes Track 0 location from the dedicated servo surface thereby eliminating mechanical transducer adjustments and related reliability concerns. The WREN 6 HH uses a high performance actuator assembly consisting of a low inertia, balanced, patented, straight arm design which provides excellent performance with minimum power dissipation. Media Description ----------------- The media used on the WREN 6 HH has a diameter of approximately 5 inches (130 mm). The aluminum substrate is coated with a thin film magnetic material, overcoated with a proprietary protective layer for improved durability and environmental protection. Each data surface has a total of 1747 tracks and is capable of recording 54,716,040 bytes of unformatted data. Media defects are characterized as correctable or uncorrectable de- pending on the type and magnitude of the media flaw. Various error correction codes may be implemented. The code chosen should be consistent with Seagate media testing and certification methods. WREN 6 HH media certification is performed using the following standards: An error burst of 11 bits or less is a correctable error. An error burst greater than 11 bits in length is an un- correctable error. Host systems using the WREN 6 HH should have, as a minimum, resident capabilities to recognize and map defective tracks and perform track reallocation routines. At the time of shipment from the point of manufacture, the WREN 6 HH recording surfaces meet the following requirements. 1. 1747 total tracks per surface. 2. Tracks 0 to be error free on each data surface. 3. 50 defects per surface maximum. 4. Cumulative defects not to exceed 1 per megabyte, based on total available unformatted drive capacity. Defect and Error Management --------------------------- The WREN 6 HH, as delivered, complies with specification. The read error rate and specified storage capacity are not dependent upon use of defect management routines. However, a carefully chosen defect management plan can significantly enhance overall system performance. Identified defects are recorded on the defects list tracks per ESDI specification. It is recommended that these known defects be re- allocated during the initial format operation. Sector reallocation is suggested because, in general, it is more efficient and may offer significant performance improvement. Error Correction Code (ECC) should be used to correct additional flaws as they occur. ECC is re- commended since most of the defects are recoverable with ECC. If ECC is not used, defects are usually unrecoverable and need to be re- allocated as they are discovered. The WREN 6 HH defect list is written on maximum track, maximum track minus eigth and a special track 4095 (OFFF) Custom Formatting ----------------- The WREN 6 HH is formatted during production. Seagate maintains custom formatting capability which can incorporate many of the unique formats used in the Winchester marketplace. A majority of special format requirements can be implemented as specified. Drive/Receiver Characteristics ------------------------------ Logic Level Drive Output Receiver Input -------------------------------------------------------------------- High (negated) (0) 2.5 V; 5.25 V 2.0 V; 5.25 V Low (asserted) (1) 0.7 V; 0.0 V 0.8 V; 0.0 V The difference in the voltages between input and output signals is due to the losses in the cable. Seek Time --------- |WREN 6HH| ----------------------------------+--------+ Track-to-Track msec. typ. | 3 | msec. max. | 5 | Average msec. typ. | 16 | Average msec. max. | 18 | Latency msec. avg. | 8.35 | ----------------------------------+--------+ Seek time is defined as the elapsed time from the receipt of a seek command until the drive signals the controller that it is ready to perform another seek or a read/write function on the new cylinder. Average seek time is determined by dividing the sum of the time for all possible movements by the total number of movements. Spindle Speed and Latency ------------------------- The spindle speed is 3592 0.5% r/min. The speed tolerance includes motor performance and motor control circuit tolerances. The average latency time is 8.35 milliseconds, based on a nominal disc speed of 3592 r/min. The maximum latency time is 16.79 milli- seconds based on a minimum disc speed of 3574 r/min. Read Data Transfer Rate ----------------------- The nominal read serial data transfer rate is 15.0 Mbits per second. Power Sequencing ---------------- Power sequencing is not required for the WREN 6 HH. The drive protects against inadvertent writing during power up and down. Daisychain operation requires that power be maintained on the terminated WREN 6 HH to ensure proper termination of the peripherals I/O cables. Temperature ----------- 50*F to 122*F (10*C to 50*C) operating ambient with a maximum gradient of 18* F (10* C) per hour. Above 1000 feet (305 metres) altitude the maximum temperature is derated linearly to 122*F (44.4*C) at 10,000 feet (3048 metres). Cabinet packaging designs must provide ample air circulation around the WREN 6 HH to ensure environmental limits are not exceeded as a result of heat transfer from other system components. Operating ambient specifications purposes is defined as the environment immediately surrounding the WREN 6 HH. The temperature of the HDA is restricted to a maximum of 142*F (61.4*C) during operations. System cooling consideration should avoid large (>5*F or 2.8*C) thermal gradients between points A and B. Reliability ----------- The following reliability specifications assume correct host/drive operational interface, including all interface timings, power supply voltages, and environmental conditions. MTBF 40,000 hours Service Life 5 years Preventive Maintenance None required ********************************************************************** G E N E R A L ********************************************************************** SEAGATE SUPPORT SERVICES Seagate Technology ------------------ Technical Support Services If you need assistance installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional assistance with your Seagate(r) drive or other Seagate products, use one of the Seagate technical support services listed below. SeaFONE at 1-800-SEAGATE (1-800-732-4283) Seagate's 800 number allows toll-free access to automated self-help services, providing answers to commonly asked questions, troubleshooting tips and specifications for disc drives and tape drives. This service is available 24 hours daily and requires a touch-tone phone. If you need to speak to a technical support engineer, dial this number and listen to the options for technical support. (International callers can also reach this automated self-help service by dialing 408-456-4496). Seagate Technology online services Using a modem, you can obtain troubleshooting tips, free utility programs, drive specifications and jumper settings for Seagate's entire product line. You can also download software for installing and analyzing your drive. SeaNET You can obtain technical information on Seagate drives, Seagate software and much more over the Internet from Seagate's World Wide Web home page (http://www.seagate.com) or Seagate's ftp server (ftp://ftp.seagate.com). You may also send E-mail with your questions to DiscSupport@ Seagate.com or TapeSupport@Seagate.com. SeaBOARD SeaBOARD is a computer bulletin board system (BBS) that contains information about Seagate's disc and tape drive products and is available 24 hours daily. Set your communications software to eight data bits, no parity and one stop bit (8-N-1). SeaBOARD phone numbers are listed in the following table. BBS Location Modem number United States Disc: 408-434-1080; Tape: 408-456-4415 England 44-1628-478011 France 33 1-48 25 35 95 Germany 49-89-140-9331 Singapore 65-292-6973 Thailand 662-531-8111 Australia 61-2-9756-2359 Taiwan 886-2-719-6075 Seagate CompuServe forum Online technical support for Seagate products is available on CompuServe. To access our technical support forum, type go seagate. This forum provides information similar to that found on SeaBOARD. In addition, you can type questions or browse through previous questions and answers on the forum messages. Seagate Technology FAX services SeaFAX You can use a touch-tone telephone to access Seagate's automated FAX system to receive technical support information by return FAX. This service is available 24 hours daily. Location Telephone number United States 1-800-SEAGATE or 408-456-4496 England 44-1628-894084 Australia 61-2-9756-5170 Seagate technical support FAX You can FAX questions or comments to technical support specialists 24 hours daily. Responses are sent during business hours. Location FAX number United States 408-944-9120 England 44-1628-890660 France 33 1-46 04 42 50 Germany 49-89-1430-5100 Australia 61-2-9725-4052 Singapore 65-293-4722 Hong Kong 852-2368 7173 Taiwan 886-2-715-2923 Korea 82-2-556-7294/4251 Seagate technical support You can talk to a technical support specialist during business hours Monday through Friday for one-on-one technical help. Before calling, note your system configuration and drive model number (STxxxx). There are several technical support phone numbers available for various Seagate products. Location Telephone number United States Please dial 1-800-SEAGATE for the specific product telephone number. (6:00 A.M. to 11:15 A.M., 12:30 P.M. to 5:00 P.M., Pacific time, M-F) England 44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to 5:00 P.M., M-F) France 33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 5:00 P.M., M-F) Germany Disc: 49-89-140-9332; (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 4:00 P.M., M-F) Tape: 49-89-140-9333 Australia 61-2-9725-3366 (9:00 A.M. to 5:00 P.M., M-F) Singapore 65-290-3998 (9:00 A.M. to 12:00 P.M., 2:00 P.M. to 5:00 P.M., M-F) Hong Kong 852-2368 9918 Taiwan 886-2-514-2237 Korea 82-2-556-8241 SeaTDD 408-944-9121 Using a telecommunications device for the deaf (TDD), you can send questions or comments 24 hours daily and exchange messages with a technical support specialist between 6:00 A.M. to 11:15 A.M. and 12:30 P.M. to 5:00 P.M. (Pacific time) Monday through Friday. Customer Service Centers Seagate direct OEM, Distribution, System Integrator and Retail customers should contact your Seagate Service Representative for warranty information. Other customers contact your place of purchase. Seagate offers comprehensive customer support for all Seagate drives. Seagate customer service centers are the only facilities authorized to service Seagate drives. These services are available worldwide. Location Telephone number FAX number United States 1-800-468-3472; 405-949-6740 Other Americas (Canada & Brazil) 405-949-6706; 405-949-6738 Mexico 525-546-6965; 525-546-4888 Europe, Middle East & Africa 31-2065-43300; 31-2065-34320 Asia Pacific & Australia 65-485-3595; 65-485-4980 Japan 81-3-5462-2904; 81-3-3462-2979 Seagate, Seagate Technology and the Seagate logo are registered trademarks of Seagate Technology, Inc. SeaFAX, SeaFONE, SeaBOARD, SeaTDD, SeaNET, Medalist and DiscWizard are either trademarks or registered trademarks of Seagate Technology, Inc. or one of its subsidiaries. All other trademarks or registered trademarks are the property of their respective owners.