7 1 0 0 0 A MAXTOR NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders | 1946| | Capacity form/unform 1002/ MB Heads | 16| | Seek time / track 13.0/ ms Sector/track | 63| | Controller IDE / ATA2 FAST/ENHA Precompensation Cache/Buffer KB Landing Zone Data transfer rate MB/S int Bytes/Sector 512 11.100 MB/S ext Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek W Rotation RPM read/write W Acoustic dBA spin-up W ECC Bit MTBF h Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MAXTOR 71000A QUICK REFERENCE +---------------------------------------------------------+ | J20*****J24 | | COMPONENT SIDE ***** |XXI | |XXN | |XXT | |XXE | |XXR J1 | |XXF | |XXA | |XXC | |XXE | |XX | |XX | |XX | | 1 | 1XX Power | |XX J2 +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** MAXTOR 71000A QUICK REFERENCE Jumper Setting ============== Jumper Designation ------------------ +---------------- J20 | +------------- J21 RESERVED! | | +---------- J22 RESERVED! * * * * * * * * * * | | | +---- J24 SPARE JUMPER +------- J23 SPARE JUMPER +-----------------------+------+ | | J20 | +-----------------------+------+ | Master/Slave | | | Only Drive in system |CLOSED|(default) +-----------------------+------+ | Master (Primary) |CLOSED| +-----------------------+------+ | Slave (Secondary) |OPEN | +-----------------------+------+ DC Power connector ------------------ pin 1 +12 VDC pin 2 +12 Volts Return pin 3 + 5 Volts Return pin 4 + 5 VDC ********************************************************************** G E N E R A L ********************************************************************** MAXTOR IDE INSTALLATION INSTALLATION PROCEDURE FOR AN IDE DRIVE --------------------------------------- 1. Install a 40 pin Data Cable ensuring that pin 1, which can be identified by the striped edge of the cable, is closest to the power connector on the drive. 2. Install a DC power cable to the back of the drive. 3. Verify the jumper configurations for Master/Slave operation (Note: Master will be the bootable drive. The slave will not be bootable.) Also make sure the existing C: drive is jumped to be the Master in a two drive system, not the only drive in the system. 4. Apply power to the computer. 4a. When memory test is complete go into your system's Standard CMOS set-up. (Note: There are various ways to get into CMOS set-up, please refer to system's manual for instructions.) 4b. If your system's BIOS supports a user programmable drive type, program the BIOS with the default parameters of your drive. If your system does not support a user programmable drive type choose parameters that closely match but do not exceed the drives MegaByte capacity. Escape from set-up then choose write to CMOS and exit. 5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on it. At the A> prompt type in FDISK. At the menu options select option 1 to create a DOS partition. Another menu will appear and from those options choose 1 to create a Primary DOS partition. Select yes to make 1 large partition and it will automatically become active. Then escape from FDISK. 6. At the A> prompt type in FORMAT C:/S This does a high-level format on the drive and transfers the system files in order for the drive to be bootable. (Note: IDE drives are low-level formatted from the manufacturer and only need a high-level format). To configure the drive as a slave drive repeat steps 1-4 and proceed with steps 5a. and 6a. as follows: 5a. At the C> prompt type in FDISK. When the menu options appear select option 5 to switch to the second drive. Enter fixed disk drive number 2. Then choose option 1 to create a DOS partition, then select option 1 again to create a Primary DOS partition or option 2 to create an Extended DOS partition. (Note: C and D drives will always be the Primary partitions but only the Primary partition on C: will have a status of active). 6a. Proceed with a high-level format on the drive by typing FORMAT D: (Note: Make sure the correct drive letter has been selected for format). 7. The drive is now bootable. As a test remove the DOS diskette from A and press reset to reboot the computer, a C> should be displayed, the drive is now ready for operation.